To provide the best experiences, we use technologies like cookies to store and/or access device information. Consenting to these technologies will allow us to process data such as browsing behavior or unique IDs on this site. Not consenting or withdrawing consent, may adversely affect certain features and functions.
The technical storage or access is strictly necessary for the legitimate purpose of enabling the use of a specific service explicitly requested by the subscriber or user, or for the sole purpose of carrying out the transmission of a communication over an electronic communications network.
The technical storage or access is necessary for the legitimate purpose of storing preferences that are not requested by the subscriber or user.
The technical storage or access that is used exclusively for statistical purposes.
The technical storage or access that is used exclusively for anonymous statistical purposes. Without a subpoena, voluntary compliance on the part of your Internet Service Provider, or additional records from a third party, information stored or retrieved for this purpose alone cannot usually be used to identify you.
The technical storage or access is required to create user profiles to send advertising, or to track the user on a website or across several websites for similar marketing purposes.
Some new sample questions:
Question:
Which of the following fields are contained in an ARP packet?
A. Source Protocol Address
B. Source Hardware Address
C. Hardware Type
D. Operation Code
Question:
On the Huawei VRP, what is the default preference of different route types, in descending order?
A. Direct > Static > RIP > OSPF
B. Direct > OSPF > RIP > Static
C. Direct > RIP > Static > OSPF
D. Direct > OSPF > Static > RIP
Question:
Which of the following advantages is/are provided by inter-VLAN routing in one-arm routing mode?
A. Reduced use of IP addresses
B. Reduced number of links
C. Reduced number of entries in the routing table
D. Reduced number of devices
Question:
For an Eth-Trunk in LACP mode, what is the default LACP system priority of a Huawei switch?
A. 4096
B. 36864
C. 32768
D. 24576
Question:
If Spanning Tree Protocol (STP) is disabled on the network consisting of switches, a Layer 2 loop will definitely occur.
A. TRUE
B. FALSE
……
Some new questions:
Q
Refer to the graphic, which of the following statements is true about OSPF topology and configuration?
A. Compared with R1, R2 is more likely to become the DR because the DR priority of the interface on R2 is lower than that of R1.
B. After the default network type of the interface on R1 is restored to broadcast, a stable OSPF neighbor relationship can be set up between R1 and R2.
C. After the default network type of the interface on R1 is restored to broadcast and the hello packet sending interval is changed to 10s, a stable OSPF neighbor relationship can be set up between R1 and R2.
D. A stable OSPF neighbor relationship can be set up between R1 and R2.
Q
On the command line interface of Huawei AR routers, the role of the Save command is to save the current system time.
A. TRUE
B. FALSE
Q
On the VRP, when the mkdir test command is run, the system creates a directory named test.
A. TRUE
B. FALSE
Q
The router ID of the OSPF process takes effect immediately after being changed.
A. TRUE
B. FALSE
Q
Which of the following IPv4 addresses can be directly used by a host to access the Internet?
A. 172.32.1.1/24
B. 10.255.255.254/24
C. 192.168.1.1/24
D. 172.16.255.254/24
Q
In the following figure, after the OSPF routers converge, in which state is the OSPF neighbor relationship between Router B and Router C?
A. Full
B. Down
C. 2-way
D. Attempt
Q
Which of the following parameters is not contained in STP configuration BPDUs?
A. Bridge ID
B. VLAN ID
C. Root ID
D. Port ID
Q
Which of the following descriptions about STP designated ports is correct?
A. Designated ports are responsible for sending BPDU to connected network segments.
B. Designated ports forward frames destined for the root switch.
C. Each bridge can have only one designated port.
D. Designated ports represent the path leading to the root switch.
……